“We maintain a large inventory in our warehouse so we are ready
to ship to you when you need it most"

FLOORS

High Speed Burnishing Program

INITIAL APPLICATION:

Deep scrub or strip floor. Rinse / neutralize floor. Pre-burnish entire floor if possible. Apply 4 medium coats of Tuff-Plus. Make sure each coat is completely dry (15-30 min.) before reapplying consecutive coats. After the fourth coat apply 1 medium coat of Thermo-After Shock, (T-A2) to entire floor. Aggressively mop on T-A2 as if cleaning floor to allow complete penetration and absorption. T-A2 will blend perfectly and not leave lines. Allow 5-10 minutes for T-A2 to dry. Do not use blower . Burnish immediately with 1500-2000 RPM High-Speed buffer. Use an aggressive synthetic or natural hair blend burnishing pad. Burnish AGGRESSIVELY and S L O W L Y (50% slower than usual on initial setup) to allow T-A2 to completely harden to a crystal clarity . Do not wait more than one hour to burnish T-A2.

Note: In very heavy traffic environments additional coats of Tuff-Plus may be necessary for a super durable foundation. IMPORTANT - READ STEP #3

Step 1 – Daily
Dust mop. Do not use spray oil dust mop treatment. Clean with mop using Hild Chemical's Neutral Cleaner Extreme Plus (Blue Label). Pour 1-2 ounces into clean mop bucket. Fill with water. Use dedicated mop for cleaning purpose only. DO NOT USE MORE NEUTRAL CLEANER EXTREME PLUS THAN RECOMMENDED. Cleaning with a pH other than 7.5 will damage the crystalline in T-A2 and dull floor! In high traffic situations frequent burnishing may be needed for durability.

Step 2 - Weekly to Monthly
Clean first as described in step one with Hild Chemical's Neutral Cleaner Extreme Plus (Blue Label). Pour 1-2 ounces (depending on degree of dirt) in mop bucket. If necessary scrub with WHITE pad or RED (depending on degree of dirt) using 175 RPM machine. Burnish with HILD type 1500-2000 RPM High Speed Burnisher / Buffer. Use an aggressive synthetic or natural hair blend burnishing pad. Test pads for scratching . HINT: The more floor is burnished, the longer it will last between re-coats! Burnish to crystal clarity.

Step 3 - Monthly or when Floor Looses Gloss
Patch wear areas and/or high traffic areas with Hild Chemical's “Thermo-After Shock, T-A2 (Black Label)”. Pour T-A2 on DEDICATED 24-oz. rayon mop. Do not use for any other purpose. DO NOT POUR into mop bucket. Mop T-A2 over high traffic or worn areas only (after initial application of T-A2 on entire surface). T-A2 will blend perfectly and not leave lines. Burnish with 1500-2000 RPM High-Speed buffer. Use an aggressive white or synthetic burnishing pad. Burnish AGGRESSIVELY and S L O W L Y to allow T-A2 to completely harden . After using mop, cover with plastic liner or bag. Mop may be reused until worn or filled with dirt. DO NOT let mop dry. If mop dries, throw away. T-A2 will cover 4000-5000 sq. ft.

Step 4 - Bi-Monthly to Quarterly
Using 175-RPM machine scrubber, clean with RED pad and apply 1 coat of Hild Chemical's Tuff-Plus and let dry and 1 coat of

T-A2 and let dry. Burnish with 1500-2000 RPM High-Speed buffer. Burnish between coats if possible. Burnish floor until crystal clear clarity is obtained. If floor appears cloudy continue burnishing. Do not wait until more than one hour to burnish T-A2.

Step 5 - Annually / Yearly
Scrub with BLUE pad and Hild Chemical's Neutral Cleaner Extreme Plus. Apply 2-3 coats of Tuff-Plus and 1 coat of T-A2. Burnish with 1500-2000 RPM High-Speed buffer. Propane buffers will not damage the floor coatings.

Repairing Spills or Scratches
Clean ENTIRE FLOOR as described in #2. Pour 2 ounces of Hild Neutral Cleaner Extreme Plus in mop bucket. With mop, clean damaged area. Scrub damaged area with 175-RPM machine using red pad. If damage does not come off use a blue pad. Rinse with clean water. Apply 2-3 coats of Hild Tuff-Plus. Aggressively apply T-A2 over repaired area. Overlap repair area approx. 6 inches. Burnish until crystal clarity is obtained.

No-Burnishing - Tuff-Plus Only
Deep scrub or strip floor. Rinse / neutralize floor. Using 20-24 oz. Rayon Mop, apply 4-6 medium coats of Tuff-Plus. Make sure each coat is thoroughly dry before applying consecutive coats.

Step 1 – Daily
Dust mop. Do not use spray oil dust mop treatment. Clean with mop using Hild Chemical's Neutral Cleaner Extreme Plus (Blue Label). Pour 1 (one) ounce per gallon of water into clean mop bucket. Fill with water. Use dedicated mop for cleaning purpose only. DO NOT USE MORE NEUTRAL CLEANER THAN RECOMMENDED. Cleaning with a pH other than 7.5 will damage floor!

Step 2 - Weekly to Monthly or When Floor Becomes Dull or Scuffed
Clean first as described in step one with Hild Chemical's Neutral Cleaner Extreme Plus (Blue Label). Pour 1-2 ounces (depending on degree of dirt) in mop bucket. If necessary scrub with a RED pad using 175 RPM Scrub Machine.

Step 3 - Bimonthly to Quarterly
Using 175-RPM machine scrubber, clean with RED pad. Clean with Neutral Cleaner Extreme Plus as described in Step 2 using 4-6 ounces of Neutral Cleaner Extreme Plus. Rinse with clean water. Let Dry. Apply 1-2 coats of Hild Chemical's Tuff-Plus and let dry. Additional coats may be necessary. ALLOW SUFFICIENT DRY TIME BETWEEN COATS, FROM 15-30 MINUTES.

Step 4 - Annually / Yearly
Scrub with BLUE pad and Hild Chemical's Neutral Cleaner Extreme Plus. Apply 2-3 coats of Tuff-Plus.

For technical Information call:

HILD CHEMICAL, INC.
18437 Mt. Langley, Ste. P
Fountain Valley, CA 92708
Phone: (562) 916-3319 / Fax: (562) 366-1727

www.hildchemical.com